AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateTrusted Furnace Replacement for Richardson Homeowners
A furnace that’s limping through January is a problem you can postpone, but not for long. When repairs start stacking up and the heat never quite reaches the back bedrooms, replacement usually costs less over the next few winters than another round of fixes. Our technicians have up to 14 years of experience and arrive already familiar with the major systems Richardson homes run on, from Carrier and Trane to Goodman and Lennox. We offer same-day service on many furnace replacement calls, and our estimates are free. Call (855) 419-6908 and we’ll get a written price in your hands.
What Our Furnace Replacement Service Includes
Replacement isn’t one task. It’s a sequence: figure out why the old unit failed, size the new one correctly for your house, pull it out cleanly, set the new furnace, and prove it’s heating the way it should before we leave. Here’s what we bring to each part of the job.
Sizing and Load Assessment
Before we quote anything, we look at your home’s square footage, window load, insulation, and duct layout so the new furnace matches the house rather than the old unit’s label. An oversized furnace short-cycles, wears out faster, and leaves hot and cold spots in Richardson’s midsize ranch homes. An undersized one runs constantly and never catches up on the coldest mornings. We put the assessment in writing so you can see the reasoning behind the size we recommend.
System Removal and Disposal
The old furnace comes out whole, along with the venting, flue connections, and any worn gas fittings that won’t safely carry over to a new unit. We haul the old equipment away rather than leaving it in your garage or alley. During removal we also check the heat exchanger and flue path for corrosion or debris, because a new furnace sitting on a compromised vent is a problem waiting to happen.
New Furnace Installation
We set the new unit level, reconnect gas and electrical, seal the plenum and duct connections, and confirm clearances to combustibles meet code. Your new furnace gets commissioned properly: gas pressure checked, blower speed set, temperature rise measured against the manufacturer’s spec. We also program the thermostat to your household’s schedule so the system doesn’t default to a setting that wastes gas.
Duct and Airflow Check
A new furnace can’t fix ducts that leak or choke airflow, so we inspect the supply and return runs before we call the job finished. Richardson homes built in the 1970s and 1980s often have undersized returns that strain a new blower from day one. If we find a restriction we’ll show you what it is and quote the fix separately. You decide whether to address it now or later.
Startup, Testing, and Walkthrough
Every replacement ends with a full cycle test: heat call, ignition, blower ramp, temperature rise, and a carbon monoxide check on the flue. We walk you through the thermostat, the filter location and size, and what to expect during the first week of operation. You get the manufacturer’s documentation and our written record of the readings we took.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Brands We Service for Furnace Replacement
We’re certified to install and repair nine of the most widely-owned HVAC brands in North Texas. On the heating side that means we can size and set a Carrier furnace, swap out an aging Trane unit, or replace a builder-grade Goodman without sending you to another contractor. Each brand has its own quirks. Carrier’s newer condensing models want specific venting arrangements. Trane’s cabinet dimensions and plenum patterns differ enough from other makes that a straight swap isn’t always straight. We know those differences before we arrive.
Higher-end Lennox furnaces have their own control boards and airflow programming, and we work with them often enough to set them up correctly the first time rather than learning on your dime. Whether you have Carrier, Trane, Lennox, Goodman, or any other make, we can help. If your equipment isn’t one we’re certified on, we’ll tell you upfront instead of guessing. And if you’re looking at Juniper AC Repair for both heating and cooling, you won’t need a second company when the AC side needs attention.
Signs You Need Furnace Replacement Right Now
- Repairs are piling up. If you’ve paid for three or more fixes in two heating seasons, the pattern is telling you something. At that point the annual repair bill often approaches the cost of a new unit, and the failures tend to come in the coldest weeks. Richardson winters are mild enough that a failing furnace can limp along for a while, which makes it easy to put off the decision until it quits outright.
- Your gas bill is climbing without a reason. A furnace losing efficiency burns more gas to produce the same heat. If your usage is up while your habits haven’t changed, the unit is telling you it’s working harder than it should. A cracked heat exchanger or dirty burners are common culprits, and both are worth a professional look before you decide to replace.
- Rooms never get warm. Uneven heat, cool bedrooms, or a system that runs nonstop on a 40-degree night can point to a furnace that’s undersized or simply worn out. It can also point to duct problems, which is why we check both before recommending replacement. Nobody should pay for a new furnace when the real fix is a return duct.
- You’re seeing yellow flames or soot. A healthy gas flame burns blue. Yellow flames, soot around the burner compartment, or a metallic smell in the house are signs of incomplete combustion and a potential carbon monoxide risk. Stop using the furnace and call a trained professional right away. This is one of the few situations where we’d rather you shut the system down and call than wait for a convenient day.
- The unit is old enough to be a question mark. Furnaces typically last 15 to 20 years. Once yours crosses that line, every season is borrowed time, and replacement parts get harder to source. A planned replacement in mild weather is far easier than an emergency one in a cold snap.
Our Furnace Replacement Process – Step by Step
- 1
Call and book. Reach us at (855) 419-6908. We answer 24/7 and schedule fast dispatch from 7am to 7pm, Sunday through Friday. We’ll ask about the age and make of your furnace so the technician arrives prepared rather than making two trips.
- 2
On-site evaluation. The technician inspects the furnace, the venting, the gas line, and the duct system, then measures the house for load. Combustion analysis and a temperature-rise reading tell us whether the current unit failed from age, sizing, or a venting issue, and that diagnosis shapes the replacement.
- 3
Written estimate. You get a line-item quote covering equipment, labor, removal, and any duct or venting work, with the model number spelled out. Pricing is per job and set by the written estimate, so there are no surprises at the end. If we recommend a repair instead of replacement, we’ll say so.
- 4
Scheduling and installation. Once you approve, we order the equipment and set an install date. Most replacements are completed in a day. We protect floors, work clean, and keep you informed as the job moves through removal, setting, and connection.
- 5
Testing and handoff. We run the system through a full heating cycle, verify gas pressure and temperature rise, and check for carbon monoxide at the flue. Then we walk you through the thermostat, filter, and what to watch for in the first week. If anything reads off, we correct it before we leave.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Furnace Replacement Cost in Richardson?
Most furnace replacements in Richardson fall somewhere between what a straightforward swap and a full system change-out cost, and the equipment tier you choose moves that number more than anything else. A furnace repair runs $150 – $700 when the unit is fixable, which is why we always quote repair first if it makes sense. When it doesn’t, the replacement quote is itemized so you can see exactly where the money goes.
| Scenario | Typical Estimated Range |
|---|---|
| Furnace repair (when the unit is still viable) | $150 – $700 |
| Standard-efficiency furnace replacement | Written estimate per job |
| High-efficiency furnace replacement | Written estimate per job |
| AC installation (for comparison, cooling side) | $3,500 – $7,500 |
| Seasonal tune-up | $80 – $200 |
What affects the price: equipment efficiency tier, furnace size relative to your home’s load, whether venting needs modification, duct repairs discovered during inspection, and whether the gas line needs upgrading. To avoid overpaying, get the quote in writing with model numbers, ask whether the price includes removal and disposal, and don’t let anyone talk you into a bigger furnace than the load calculation supports. Our free estimate includes all of that. The written estimate sets the final price, and we can work with your insurer if a covered event is involved.
Furnace Replacement Near Richardson – Our Service Area
We serve homeowners across Richardson and the surrounding cities, including Plano, Garland, Allen, Carrollton, Dallas, Mesquite, Lewisville, Irving, and Duncanville. Scheduling depends on the day and the season, but we keep fast dispatch from 7am to 7pm, Sunday through Friday, and our team is a phone call away whenever you need to book. We answer 24/7. A call outside dispatch hours is booked into the next opening.
Serving Richardson, TX – Our Local Coverage Area
We serve Richardson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Furnace Replacement in Richardson
Furnace replacement means removing your existing heating unit and installing a new one sized for your home, including the venting, gas connection, and duct interface. It’s different from a repair, which fixes a specific failed component on equipment that’s otherwise sound. Replacement makes sense when the unit is past its service life, when the heat exchanger has failed, or when repair costs start repeating. We always evaluate whether a repair will get you another few seasons before recommending replacement.
Most residential replacements are completed in a single day, typically six to eight hours once the equipment is on site. The timeline stretches if venting needs modification, if we find duct problems during removal, or if the job requires a permit inspection. We give you a realistic window when we schedule, not a vague one. If the work runs into a second day, we’ll tell you before we leave on the first.
Replacement pricing is set per job by a written estimate, because equipment tier, furnace size, and venting needs vary so much from house to house. Furnace repair, for comparison, typically runs $150 – $700 when the unit is fixable. The free estimate itemizes equipment, labor, removal, and any duct or venting work, so you can compare across quotes on equal terms. Call (855) 419-6908 for an exact quote; estimates are free.
Yes. We’re certified to install and repair nine major HVAC brands, including Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That means our technicians arrive already familiar with your equipment’s control layout, venting requirements, and common failure points. We can also recommend a different brand if your home’s load or duct system points that way. Call (855) 419-6908 and tell us what you have.
Same-day replacement is possible when the equipment is available and the diagnosis is straightforward, though most replacements are scheduled for a set install date after the estimate is approved. Repair calls often qualify for same-day service. For more detail on that side of the work, see our Garland page. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (855) 419-6908 to check availability.
Your new furnace carries the manufacturer’s equipment warranty, which typically covers parts for a set term, and we stand behind our installation labor. We register the equipment with the manufacturer on your behalf and leave the documentation with you. Warranty terms differ by brand and model, and we’ll spell out yours in the written estimate before you commit. If you’re also planning cooling work later, our Allen page covers AC installation and what that involves.
Clear the area around the furnace and the path from your entry door so the technicians can move equipment without moving your belongings. Secure pets in a room away from the work area, and plan for the noise of removal and testing. If the old furnace is your only heat source, expect the house to cool during the day, so dress accordingly. Have your thermostat manual and any service records handy. Call (855) 419-6908 with questions before the crew arrives.
Schedule Your Furnace Replacement Service in Richardson Today
Don’t wait for a cold snap to find out your furnace has given up. Call (855) 419-6908 to book a free, no-obligation estimate for furnace replacement in Richardson. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 14 years of experience working with Carrier, Trane, Lennox, Goodman, and more. You’ll get a written price, a set install date, and a system that heats the way it should.
Written by the team at Juniper AC Repair.